Search found 19 matches

by Redemptioner
Fri Mar 02, 2018 10:00 am
Forum: General
Topic: Tevo Seriously Need to take a hard look at themselves
Replies: 10
Views: 4156

Re: Tevo Seriously Need to take a hard look at themselves

There is no excuse for the poor electronics at this price range. Stick included with the bed is pretty good, I have over 150 prints on it and still going strong without issue, glass is nowhere near as good and always has the risk of being damaged and it is much harder to be replace than a $15 sticke...
by Redemptioner
Sun Feb 04, 2018 11:49 pm
Forum: Troubleshooting
Topic: Y,Z end stops not working
Replies: 5
Views: 1246

Re: Y,Z end stops not working

Yes, all should be voltage, ground, signal from right to left. Keep in mind there will be a 5V output for the signal on the one for the Z-probe (BL touch). It is super strange for these to be connected up differently as they are set as traces on the PCB, you can try changing the pin layout on one of...
by Redemptioner
Sun Feb 04, 2018 11:03 pm
Forum: General
Topic: Tevo Seriously Need to take a hard look at themselves
Replies: 10
Views: 4156

Re: Tevo Seriously Need to take a hard look at themselves

Well Filastruder is a genuine product supplier of E3D and is stated and linked too on E3D sites so there is no concern to be raised about going with them. Let's no cause any misinformation there. I have personally found Filastruder to be far higher in customer service than E3D directly, they are muc...
by Redemptioner
Sun Feb 04, 2018 11:03 pm
Forum: Hardware
Topic: Upgrade you Tevo Little Monster - Pro Addition
Replies: 8
Views: 3102

Upgrade you Tevo Little Monster - Pro Addition

This coming weeks I will be posting up all the detail and the items needed to bring your Tevo Little Monster up to a PRO level. These upgrades and modifications not only significantly improve the print speed and quality it also drastically increases the the range of plastics you can print and ensure...
by Redemptioner
Fri Jan 05, 2018 3:36 am
Forum: Troubleshooting
Topic: Calibration
Replies: 1
Views: 671

Re: Calibration

connect via the usb with pronterface, then type in the G-code in this order G28 (send printer to home) G29 (run a full calibration) M500 (save changes) Once you have done this then power cycle the printer and reconnect to pronterface then G28 (home) G0 Z0 (go to where it thinks Z 0 is) - use the jog...
by Redemptioner
Wed Jan 03, 2018 4:16 am
Forum: Prints
Topic: Printing Tips
Replies: 10
Views: 2933

Re: Printing Tips

images
by Redemptioner
Wed Jan 03, 2018 4:14 am
Forum: Prints
Topic: Printing Tips
Replies: 10
Views: 2933

Re: Printing Tips

images
by Redemptioner
Wed Jan 03, 2018 4:12 am
Forum: Prints
Topic: Printing Tips
Replies: 10
Views: 2933

Re: Printing Tips

images
by Redemptioner
Wed Jan 03, 2018 4:09 am
Forum: Prints
Topic: Printing Tips
Replies: 10
Views: 2933

Re: Printing Tips

images
by Redemptioner
Wed Jan 03, 2018 3:01 am
Forum: General
Topic: Tevo Seriously Need to take a hard look at themselves
Replies: 10
Views: 4156

Tevo Seriously Need to take a hard look at themselves

I wanted to start a thread about the major quality issues and the poor choices Tevo has made in putting together this Delta system. Hopefully Tevo will take a look at this thread and correct these issues, I am certainly more than happy to lend them some of my time as an engineer to work on resolving...